+49 (0) 6021 / 40 27-0

Threaded transport anchor - straight version

Straight tail threaded transport anchors can be used universally for various precast concrete elements on the one hand, but on the other hand they can show their capabilities in e.g. bar-shaped elements or walls. Either with extremely thin or heavy prefabricated elements – depending on the element type and its dimensions different sizes are available. Axial-, diagonal and lateral tension are no problem for the threaded anchor with straight tail.

no parts projecting above the element's surface
small recesses on the concrete surface
resistant to light soiling due to special round thread

Lifting loop with threaded end

For the complete range of PHILIPP Threaded transport anchors the Lifting loop with threaded end, consisting of a galvanised wire rope, can be used for axial and diagonal tension.

Lifty

For a daily use in the precast plant or on the construction site the Lifty is a robust and universally applicable lifting device for the PHILIPP threaded anchor system. It consists of a forged ring bolt with a welded chain link, both galvanised.

Lifty with wire rope

The Lifty with wire rope is a universally applicable lifting device for the PHILIPP threaded anchor system. It consists of a forged ring bolt with a thread and galvanised pressed-steel wire rope.

Wirbelstar

The Wirbelstar is a lifting device for the PHILIPP threaded anchor system which is particularly suitable for lateral and diagonal tension load cases. Therefore it can be used excellently for the erecting of e.g. horizontally manufacured elements.

Wirbelstar KH

The Wirbelstar is a lifting device for the PHILIPP threaded anchor system which is particularly suitable for lateral and diagonal tension load cases. Therefore it can be used excellently for the erecting of e.g. horizontally manufacured elements. Futhermore, the PHILIPP Wirbelstar KH is especially designed for the KH system with extra small recesses in the precast concrete element.

Threaded transport anchor elongation

The anchor elongation is intended for applications where it is not possible to lift off directly at the transport anchor. E.g. with cubicles in prefabricated construction with subsequently mounted roof element, the transport of the complete module is thus possible. Here, the elongation is screwed into an existing threaded transport anchor (of the cubicle) through a recess in the roofing slab.

KHN system

The KHN system is the most versatile system of recess formers and lifting devices that can be used. On applications around the universal lifting device Lifty resp. Lifty with wire rope the main focus is set here.

WS system

The freely rotatable Wirbelstar lifting device, which can be used for all load directions, is the central feature of the WS system. An always correct alignment with the load direction is ensured by the ball-bearing swivel plate. Due to the large bearing area of the Wirbelstar loads up to 20 t are possible.

KH system

For demanding concrete surfaces the KH system is an ideal solution as it creates only very small recesses in the concrete element for the transport anchors.

Magnetic fixations

Magnetic fixations are used to fix threaded anchors or inserts to a steel mould.

Breaking-pin (plastic)

Breaking-pins (plastic) are used to fix threaded anchors or inserts to a mould.

Fixing disc for gluing

Fixing disc for gluing are used to fix threaded anchors or inserts to a mould.

Threaded adapter

The Threaded adapter is used to fix threaded anchors or inserts to a timber or steel mould.

Marking ring with clip

A marking ring identifies a threaded anchor in installed condition and fixes the position of an additional reinforcement by its clip.

Marking ring

Both, the identification of a threaded anchor in installed condition as well as a quick assignment to the corresponding lifting device is done by the marking ring with its color-code.

Sealing cap (plastic)

Sealing caps (plastic) close threaded inserts of all sizes independent of a recessed or surface-flush installation of the anchor.

Nailing plate for diagonal tension

Focus of this system is the recess former SZ15, which allows the transport anchor to be inclined by 15°, thus eliminating the need for an additional diagonal tension reinforcement.

Lifting loop plus

For all load directions, axial, diagonal and lateral tension, and in combination with the complete range of PHILIPP Threaded transport anchors the Lifting loop plus can be used universally.

Thread chaser

The Thread chaser is used for cleaning dirty threads. It is made of a standard screw with a milled dirt groove.

Wall
Bar-shaped element (e.g. purlin, waler, beam)
Garage
Shaft, manhole